4" IMC Conduit Fill Chart
This page shows the maximum number of conductors allowed in a 4-inch Intermediate Metal Conduit (IMC) conduit per the National Electrical Code. The 4" IMC has an internal cross-sectional area of 14.407 square inches, which determines how many wires of each size can legally fit inside. Use the tables below to quickly look up conductor capacity for your installation, or use the calculator for custom configurations.
THHN/THWN-2 Maximum Conductors in 4" IMC
THHN/THWN-2 is the most commonly used conductor type in commercial and residential wiring. The table below shows the maximum number of THHN/THWN-2 conductors allowed in this 4" IMC conduit based on NEC Chapter 9 fill rules. For 3 or more conductors the 40% fill rule applies. Values of 0 mean the conductor is too large to fit even a single wire in this conduit size.
| Wire Size | Wire Area (sq.in.) | Max Conductors | Fill at Max (sq.in.) |
|---|---|---|---|
| 14 AWG | 0.0097 | 594 | 5.7618 |
| 12 AWG | 0.0133 | 433 | 5.7589 |
| 10 AWG | 0.0211 | 273 | 5.7603 |
| 8 AWG | 0.0366 | 157 | 5.7462 |
| 6 AWG | 0.0507 | 113 | 5.7291 |
| 4 AWG | 0.0824 | 69 | 5.6856 |
| 3 AWG | 0.0973 | 59 | 5.7407 |
| 2 AWG | 0.1158 | 49 | 5.6742 |
| 1 AWG | 0.1562 | 36 | 5.6232 |
| 1/0 AWG | 0.1855 | 31 | 5.7505 |
| 2/0 AWG | 0.2223 | 25 | 5.5575 |
| 3/0 AWG | 0.2679 | 21 | 5.6259 |
| 4/0 AWG | 0.3237 | 17 | 5.5029 |
| 250 AWG | 0.3970 | 14 | 5.5580 |
| 300 AWG | 0.4608 | 12 | 5.5296 |
| 350 AWG | 0.5242 | 10 | 5.2420 |
| 400 AWG | 0.5863 | 9 | 5.2767 |
| 500 AWG | 0.7073 | 8 | 5.6584 |
About 4" Intermediate Metal Conduit
IMC provides a middle ground between EMT and RMC in terms of physical protection and cost. It is used where greater mechanical protection is needed than EMT can provide, but the full weight and cost of RMC is not justified. IMC is suitable for indoor and outdoor installations, including exposed runs in industrial environments, parking garages, and outdoor equipment connections. The 4-inch trade size is one of the standard sizes defined in NEC Chapter 9, Table 4. With an internal area of 14.407 square inches, it provides adequate space for a range of conductor sizes and counts depending on the application requirements.
IMC is made from steel with walls thicker than EMT but thinner than RMC. It uses threaded connections like RMC but weighs about one-third less. The internal diameter falls between EMT and RMC, giving it a moderate conductor capacity for each trade size.
NEC Reference: NEC Article 342 governs the installation requirements for IMC conduit. Conduit fill is calculated using NEC Chapter 9, Table 1 (fill percentages), Table 4 (conduit areas), and Table 5 (conductor areas). This calculator uses the exact values from these tables for accurate results.
Worked Example: 12 AWG THHN in 4" IMC
Here is a step-by-step example showing how to calculate conduit fill for 4 conductors of 12 AWG THHN/THWN-2 in this 4" IMC conduit. This is a common scenario for a 20-amp branch circuit requiring two hots, a neutral, and a ground.
- Identify the conduit internal area: 4" IMC = 14.407 sq.in. (from NEC Table 4)
- Identify the conductor area: 12 AWG THHN/THWN-2 = 0.0133 sq.in. per conductor (from NEC Table 5)
- Calculate total conductor area: 4 conductors x 0.0133 sq.in. = 0.0532 sq.in.
- Determine the fill percentage rule: 4 conductors uses the 40% fill rule (NEC Table 1)
- Calculate allowable fill area: 14.407 sq.in. x 0.40 = 5.7628 sq.in.
- Compare: Total conductor area (0.0532 sq.in.) is less than allowable fill (5.7628 sq.in.) — COMPLIANT
- Actual fill percentage: 0.0532 / 14.407 = 0.4%
- Maximum conductors: This 4" IMC can hold up to 433 conductors of 12 AWG THHN/THWN-2 per NEC rules
XHHW Maximum Conductors in 4" IMC
XHHW conductors use cross-linked polyethylene insulation, which provides excellent moisture and heat resistance. XHHW has slightly different insulation dimensions than THHN, resulting in different fill counts. The table below shows the maximum XHHW conductors allowed in this 4" IMC conduit.
| Wire Size | Wire Area (sq.in.) | Max Conductors |
|---|---|---|
| 14 AWG | 0.0139 | 414 |
| 12 AWG | 0.0181 | 318 |
| 10 AWG | 0.0243 | 237 |
| 8 AWG | 0.0437 | 131 |
| 6 AWG | 0.0590 | 97 |
| 4 AWG | 0.0814 | 70 |
| 3 AWG | 0.0962 | 59 |
| 2 AWG | 0.1146 | 50 |
| 1 AWG | 0.1534 | 37 |
| 1/0 AWG | 0.1825 | 31 |
| 2/0 AWG | 0.2190 | 26 |
| 3/0 AWG | 0.2642 | 21 |
| 4/0 AWG | 0.3197 | 18 |
| 250 AWG | 0.3904 | 14 |
| 300 AWG | 0.4536 | 12 |
| 350 AWG | 0.5166 | 11 |
| 400 AWG | 0.5782 | 9 |
| 500 AWG | 0.6984 | 8 |
Installation Advantages of IMC
Lighter than RMC while providing threaded connections. Good mechanical protection for outdoor and industrial use. Can be used in direct burial applications with appropriate corrosion protection. Approved for all locations where RMC is permitted.
Installation Requirements
IMC uses threaded fittings and couplings. Threads can be cut in the field using standard pipe-threading equipment. Supports are required within 10 feet of each box and at intervals not exceeding 10 feet. Maximum 360 degrees of bends between pull points.
When planning your installation with 4" IMC conduit, remember that the fill calculation only addresses the straight sections. The number of bends, total conduit length, and pulling tension also affect whether the installation is practical. The NEC limits total bends to 360 degrees (four 90-degree bends) between pull points. For long runs or runs with many bends, consider using the next larger conduit size even if the fill calculation passes, as this will reduce pulling tension and make future maintenance easier.
Other IMC Sizes
Browse fill charts for other Intermediate Metal Conduit trade sizes. Larger conduit sizes accommodate more conductors and are needed for high-ampacity circuits or runs with many wires.